IEEE-transaction模板

如有侵权，请联系网站删除，仅供学习与交流

IEEE-transaction

模板

【精品文档】

第 1 页

如有侵权，请联系网站删除，仅供学习与交流

Preparation of Papers for IEEE T

RANSACTIONS

and J

OURNALS

(May 2007)

First A. Author, Second B. Author, Jr., and Third C. Author, Member, IEEE



Abstract—These instructions give you guidelines for preparing

papers for IEEE T

RANSACTIONS

and J

OURNALS

. Use this

document as a template if you are using Microsoft Word 6.0 or

later. Otherwise, use this document as an instruction set. The

electronic file of your paper will be formatted further at IEEE.

Define all symbols used in the abstract. Do not cite references in

the abstract. Do not delete the blank line immediately above the

abstract; it sets the footnote at the bottom of this column.

Index Terms—About four key words or phrases in alphabetical

order, separated by commas. For a list of suggested keywords,

send a blank e-mail to keywords@ or visit

/organizations/pubs/ani_prod/

I. I

NTRODUCTION

T

HIS document is a template for Microsoft Word versions

6.0 or later. If you are reading a paper or PDF version of

this document, please download the electronic file,

, from the IEEE Web site at

/web/publications/authors/transjnl/

so

you can use it to prepare your manuscript. If you would prefer to

use LATEX, download IEEE’s LATEX style and sample files

from the same Web page. Use these LATEX files for formatting,

but please follow the instructions in or

.

If your paper is intended for a conference, please contact your

conference editor concerning acceptable word processor

formats for your particular conference.

When you open , select “Page Layout”

from the “View” menu in the menu bar (View | Page Layout),

which allows you to see the footnotes. Then, type over sections

Manuscript received October 9, 2001. (Write the date on which you

submitted your paper for review.) This work was supported in part by the U.S.

Department of Commerce under Grant BS123456 (sponsor and financial

support acknowledgment goes here). Paper titles should be written in uppercase

and lowercase letters, not all uppercase. Avoid writing long formulas with

subscripts in the title; short formulas that identify the elements are fine (e.g.,

"Nd–Fe–B"). Do not write “(Invited)” in the title. Full names of authors are

preferred in the author field, but are not required. Put a space between authors’

initials.

F. A. Author is with the National Institute of Standards and Technology,

Boulder, CO 80305 USA (corresponding author to provide phone:

303-555-5555; fax: 303-555-5555; e-mail: author@ ).

S. B. Author, Jr., was with Rice University, Houston, TX 77005 USA. He is

now with the Department of Physics, Colorado State University, Fort Collins,

CO 80523 USA (e-mail: author@).

T. C. Author is with the Electrical Engineering Department, University of

Colorado, Boulder, CO 80309 USA, on leave from the National Research

Institute for Metals, Tsukuba, Japan (e-mail: author@).

【精品文档】

第 2 页

of or cut and paste from another document

and use markup styles. The pull-down style menu is at the left of

the Formatting Toolbar at the top of your Word window (for

example, the style at this point in the document is “Text”).

Highlight a section that you want to designate with a certain

style, then select the appropriate name on the style menu. The

style will adjust your fonts and line spacing. Do not change the

font sizes or line spacing to squeeze more text into a limited

number of pages. Use italics for emphasis; do not underline.

To insert images in Word, position the cursor at the insertion

point and either use Insert | Picture | From File or copy the image

to the Windows clipboard and then Edit | Paste Special | Picture

(with “float over text” unchecked).

IEEE will do the final formatting of your paper. If your paper

is intended for a conference, please observe the conference page

limits.

II. P

ROCEDURE FOR

P

APER

S

UBMISSION

A. Review Stage

Please check with your editor on whether to submit your

manuscript as hard copy or electronically for review. If hard

copy, submit photocopies such that only one column appears

per page. This will give your referees plenty of room to write

comments. Send the number of copies specified by your editor

(typically four). If submitted electronically, find out if your

editor prefers submissions on disk or as e-mail attachments.

If you want to submit your file with one column electronically,

please do the following:

--First, click on the View menu and choose Print Layout.

--Second, place your cursor in the first paragraph. Go to

the Format menu, choose Columns, choose one column Layout,

and choose “apply to whole document” from the dropdown

menu.

--Third, click and drag the right margin bar to just over 4

inches in width.

The graphics will stay in the “second” column, but you can

drag them to the first column. Make the graphic wider to push

out any text that may try to fill in next to the graphic.

B. Final Stage

When you submit your final version (after your paper has

been accepted), print it in two-column format, including figures

and tables. You must also send your final manuscript on a disk,

via e-mail, or through a Web manuscript submission system as

directed by the society contact. You may use Zip or CD-ROM