FreedomCharge Max 无线充电安装指南说明书

​

INSTALLATION INSTRUCTIONS

FreedomCharge Max Installer Kit

(Kit # FDMC-1310)

​

Visit /1310Tempate for FAQ’s and vehicle specific templates!

Please read thoroughly before starting installation and check that kit contents are complete.

Items Included in the Kit:

Qi Wireless Charging Module

Full Size Substrate

Full Size Non Slip Mat

Power Harness with 3 amp Fuse

Foam Blocks

Double Sided Tape

These Instructions with Trim Template

Removable Consumer Product Label

​

Tools & Supplies Needed:

Plastic Trim Removal Tool

Phillips Screwdriver (if needed)

7mm, 10mm Socket Drive (if needed)

Center Punch/Scribe Tool

Power Drill

⅜​

” and 1/2” Drill Bit

*Note this product is designed to work with Qi compatible devices. Please confirm that

your device is Qi compatible before installation. Visit ​​ for phone

compatibility guide.

Safety Precautions:

●Work in well ventilated area that is clear of obstructions.

●Secure vehicle with tire chucks in both front and rear of tires.

●Turn vehicle accessories OFF and ensure ignition key is in OFF position.

●Wear safety goggles and snug fitting clothes.

●Use tools only for their intended purpose and which are in good repair.

●Only perform this task if confidence, skill, and physical ability permit.

This kit is designed to be customized to fit your specific vehicle application. The following

instructions will be your guide to show you the basic steps of the installation. Your

vehicles installation may vary from these steps shown in these instructions.

Scissors

X-Acto Knife

Wire Ties

Soldering Iron & Solder ​

(Recommended)

Tape or Heat Shrink Electrical Tubing

Multi Meter or 12V test light

1310 Instructions 3-27-19Page 1 of 8KB

​

INSTALLATION INSTRUCTIONS

Mounting module to substrate

Side A: No Outlines Side B: Square Outline w/ Carrot Locator

On Side B, Align square outline with outer edges of coil and with the

connector on the same side as the small carrot for mounting

1310 Instructions 3-27-19

KB

Page 2 of 8

​

INSTALLATION INSTRUCTIONS

Freedom Charge™ has been designed with two unique mounting possibilities to fit almost

any application. Please review sections below to determine the best solution for your

particular application. Note: Due to high heat and sun exposure, the top of the dash is

not a recommended location for mounting Freedom Charge.

Section 1: The two Types of Mounting

Drop-In Mounting (from above)

Under Mounting

1310 Instructions 3-27-19Page 3 of 8KB

​

INSTALLATION INSTRUCTIONS

Section 2: Substrate and Mat

Development

These next steps illustrate the process of

creating your vehicle specific Freedom

Charge integrated solution.

Step 1: Using the Freedom Charge Module

determine the best location for installation.

Step 4: Align mat on template in desired

location. Trace outline centering the module.

Step 2: If chosen location has mat, remove to

add in making template otherwise carefully

cut template to fit. Always start larger and

slowly trim down to ensure best fit. Make

sure to account for draft as the Freedom

Charge Module is about ½” thick. If using

the Drop-In method of attachment, a mat at

the bottom of a drafted bin may be slightly

smaller than your final substrate and mat

solution.

Step 5: With scissors trim template on traced

lines.

Step 3:​ Template is full size representation of

module with recommended minimum area.

1310 Instructions 3-27-19Page 4 of 8

KB

​

INSTALLATION INSTRUCTIONS

Step 6:​ With trimmed template placed on top

of Freedom Charge module check for correct

fit in vehicle. Make any trim adjustment(s)

needed to template to achieve perfect fit.

Step 8: Scribe outline.

Step 7:​ Cut out the four holes found on the

mat/substrate template and place template

on plastic substrate aligning mounting holes.

Make sure you’re placing your cutout

template face up on Side A (without outline)

before scoring the substrate

Step 9: Substrate can be trimmed with

scissors. Be careful to cut right on the

scribed line. Again check fit in vehicle.

1310 Instructions 3-27-19Page 5 of 8KB

​

INSTALLATION INSTRUCTIONS

Step 10: Flip Freedom Charge mat and newly

trimmed substrate upside down(Side B of

substrate facing up).

Section 3: ​

Drop-In Mounting

Step 11: Using an X-Acto knife, carefully trim

mat using substrate as guide.

Step 1: Remove the plastic cover from the

double sided tape on the top side of the

charging coil. Using the mounting directions

found on Page 2, attach your coil to Side B of

the substrate

Step 2: Place new assembly into vehicle tray

or bin to mark ½” hole location required for

power connector to pass through. Drill 1/2”

hole in marked location.

Step 12: Substrate and Mat now trimmed and

ready for assembly and mounting.

Step 3:​ Route Plug of power harness through

1/2" hole and place module in bin.

1310 Instructions 3-27-19Page 6 of 8KB

​

INSTALLATION INSTRUCTIONS

Step 4: Apply supplied double sided tape to

the bottom of charging coil. Double check

fitment of coil, substrate, and mat before

removing the plastic from the bottom side of

double sided tape. Once fitment is verified

you can clean the mounting surface of the

tray and attach the coil with substrate

Step 1: Using template created in Section 2,

mark the (4) mounting holes that will be

used to lock the mat in place once the install

is complete

Step 5: Install Non-Slip Freedom Charge Mat

to Wireless Charging Module. ​Place the 4

locator pins in corresponding holes.

Step 2: Drill the (4) 3/16 holes for the

non-skid mat location crosshairs.

Step 3: From the bottom, hold Freedom

Charge Module up firmly into mounting

location. Use the (4) ⅜” holes as guides to

mount your Charge Module underneath the

tray where it will be in the center of the

Non-skid mat.

Step 6: Proceed to Power Harness wiring

(Section 5).

Section 4: Under Mounting

Follow the next step if are mounting in a

shallow location or have adequate room and

accessibility under your surface you are

mounting to. Minimum clearance is 5/8”

under mounting location and clear of any

vehicle wiring of components prior to

installation.

Step 4: Place non-skid mat on topside of

tray/bin with the crosshair locators aligned.

1310 Instructions 3-27-19Page 7 of 8KB

​

INSTALLATION INSTRUCTIONS

Section 5: ​

Power Harness

Wiring ​

(from above)

Step 3: Connect Power Harness to Charging

Module.

Freedom Charge is powered by ignition

control 12v power source. Use a Multi-Meter

of test light or manual to determine your

vehicle power location.

Step 1: Splice Red wire of Power Harness to

the 12v ignition wire of the vehicle.

RECOMMENDED​: ​Solder wires and cover with Heat

Shrink Tubing.

Section 6: Test System and

Consumer Label

Step 41: Test system. Power the vehicle up,

wait a moment, then rest wireless charging

device on mat. When the coil connects you

will hear an audible tone indicating that a

connection has been made. If you do not

hear an audible tone, check power

connection and be sure there is no metallic

obstructions between the coil and your

device

Step 1: Reassemble vehicle​ taking care not

to bind the harness wiring when reinstalling

trim.

Step 2: Place removable consumer product

label on center of mat.

Step 2: Connect Power Harness grounding

eyelet to vehicle ground.

1310 Instructions 3-27-19

Page 8 of 8KB